02/16/2014

Plasterboard

In order to make a ceiling made of plasterboard, we need the following: Tools. Water level, hammer, screwdriver or electric drill, angle measure twice for right angles, a knife for drywall, fishing line. Materials. Dowel nails, best 6 x 60 mm, 4 mm screws on the metal, the so-called "Seeds" screws for plasterboard, U-shaped pendants, ceiling profiles UD (28-27 mm) and SD (60h27 mm). And the actual ceiling drywall sheet 1200 * 2500 * 9 mm. If the profiles are smaller than the length or width room, you must purchase low elements. This can ask the seller-adviser.

The ceiling can be single storey and three-tiered chetureh. For illustrative purposes, consider making a two-tier ceiling. First level. 1. Determination of the horizontal. Be measured height in all corners of the room. Choose the lowest angle, retreating down 4-5 cm and with a water level mark making. Then, using paint repel the cord line previously defined standards.

So how do the ceiling of plasterboard for the first time we have at this stage suggest to approach the work very seriously. As they say, look before you leap! 2. Through the profile of drill holes in the wall for dowels, and then fasten it to the UD-profile (28-27 mm). 3. On the ceiling, holding the parallel lines in increments of 60 cm by the lines held on the dowel screw the nails of our U-shaped mounting hangers. 4. We stretch the line and on it at with screws anchoring the SD profiles for suspension. If the length of the room longer than the profiles, then build them using the previously acquired to connect the elements. Between the longitudinal profiles of the transverse ribs must be secured rigidity. If you plan on mounting fixtures, but he probably will, at this stage should be icing on the profiles of the wiring. 5. Proceed to the installation of drywall.
Feb 16, 2014 6:37:47 AM

Verify your Comment

Previewing your Comment

Posted by:  | 

This is only a preview. Your comment has not yet been posted.

Working...
Your comment could not be posted. Error type:
Your comment has been posted. Post another comment

The letters and numbers you entered did not match the image. Please try again.

As a final step before posting your comment, enter the letters and numbers you see in the image below. This prevents automated programs from posting comments.

Having trouble reading this image? View an alternate.

Working...

Leave a comment

(URLs automatically linked.)

Your Information

Name and email address are required. Email address will not be displayed with the comment.

NEXT POST
Foam Blocks Products Today, the construction of tall buildings characterized by the use of bulk construction products. Prompt delivery of foam concrete blocks can provide both producers and companies involved in the implementation of this products. The use of these products significantly reduces time-consuming, labor, and therefore money. They are made mostly of ordinary heavy and light concrete. By appointment to his foam concrete blocks produced for the exterior and interior walls. The first of these is subdivided by structural elements. They are prostenochnymi, corner, parapet, peremychechnye, eaves, basement. The extent of their hardiness must be at least 25 SSE, and basements - no less than 35. In structure they are hollow and solid, one-, two-, and three layers. Outside, concrete blocks have a special decorative layer. On the inside of their covered with a layer plaster. Finish their outer surface produce a layer of a decorative solution, stain-resistant dye-or opening the concrete structure percussion instrument. Foam blocks provide building a reliable thermal insulation for many years. The most important thing that this material is not limited shelf life. Despite its durability, these products also, and still relatively lightweight, making them easier to transport. It is a quality, affordable, and very promising construction material, has virtually no drawbacks. To obtain prefabricated products are used in the manufacture of reinforced concrete - heavy, light and heat insulation concrete. Feature requirements for them is that their weight-loss structures are made of material not less than 200 marks, and of the lung, including cellular grade no lower than 50. In the factory-applied powerful forms mechanisms that can be used to make products hard mixture. This not only reduces the demand for cement, but also significantly shortens the manufacturing cycle due to more rapid hardening of the hard concrete mixtures. All the world is not forever ......
PREVIOUS POST
Screed Floor Laying ties begins with the preparation of the base. If a future screed will be a smooth concrete floor with a smooth cement surface, then for a firm grip on ties with the foundation must first be roughening of the surface roughness of mechanically or with concrete contact. Previously it is important to close all the gaps between walls and slabs of cement-sand mortar or putty, to remove grease and oil stains, remnants other materials, dust-free. You must then apply the primer deep penetration that will not only ensure better adhesion, but also to prevent water penetration into the ground. After that will be seal the walls and bottom of the walls to prevent moisture penetration, the upper edge of the insulation should be 15 cm above the level .V depending on the type of floor covering and the required quality surface for laying ties may include the following materials: screeds, dry mixes for self-leveling floors, cellular, lightweight concrete, cement-sand mortar. The choice of material also depends on the thickness of the future Ties and duration of exposure before being packed cover. Duration of hardening ties depends on its thickness, from which it is made and the type of flooring. Thus, the cement-sand mortar harden in 28 days. Pouring and leveling compounds contain various polymer additives, which influence the solidification, so the process can take anywhere from 24 hours up to a month. Ties depends on the thickness of what it is placed, what material holds a floor covering will then be selected. In any case, the minimum thickness of screed is 5 cm in this case it strengthens fittings or metal mesh. For the immediate strengthening ties apply different types of impregnations and ground depending on the purpose of sex and grade of concrete used in the material for...

smallbusinessbranding

The Typepad Team

Search

Recent Comments